Genie 2024 User Manual (2024)

PN# 37026500123 02/26/2010 REV. 1

2

OVERVIEW OF POTENTIAL HAZARDS

READ THIS SAFETY INFORMATION

Garage doors are large, heavy objects that move with the help of springs under high tension and electric motors. Since moving objects, springs under tension, and electric motors can cause injuries, your safety and the safety of others depend on the owner or user of this system to read, understand and implement the information in this manual. If you have questions or do NOT understand the information presented, contact The Genie Company or an authorized Genie

®

Dealer.

The safety alert symbol and following signal words DANGER, WARNING, and CAUTION are used throughout this manual to call attention to and identify different levels of hazard and special instructions.

This is the safety alert symbol. This symbol is placed next to signal words and messages to help you identify

important safety information

The word:

DANGER indicates an imminently hazardous situation which, if NOT avoided, will result in death or serious injury. WARNING indicates a potentially hazardous situation which, if NOT avoided, could result in death or serious injury. CAUTION indicates a potentially hazardous situation which, if NOT avoided, may result in injury or property damage.

The word

NOTE is used to indicate important steps to be followed, important considerations, or location of parts.

IMPORTANT SAFETY INSTRUCTIONS

READ AND FOLLOW ALL INSTRUCTIONS

SAVE THESE INSTRUCTIONS

SAFETY INFORMATION

POTENTIAL

HAZARD

EFFECT PREVENTION

Keep people clear of opening while door is moving.

Do NOT allow children to play with the door operator. Do NOT operate a door that jams or one that has a broken spring.

MOVING DOOR

WARNING:

Could result in Death

or Serious Injury

Turn OFF power before removing operator cover. When replacing cover, make sure wires are not pinched or near

moving parts. Operator must be properly grounded.

ELECTRICAL

SHOCK

WARNING:

Could result in Death

or Serious Injury

Do NOT try to remove, install, repair or adjust springs or anything to which door spring parts are fastened, such as, wood blocks, steel brackets, cables or other like items.

Installations, repairs and adjustments must be done by a trained door system technician using proper tools and instructions.

HIGH

SPRING

TENSION

WARNING:

Could result in Death

or Serious Injury

PN# 37026500123 02/26/2010 REV. 1

3

TABLE OF CONTENTS

OPENER FEATURES

INTELLICODE®Rolling Code Security System.

An electronic rolling code system that enhances the security of the door opener by continuously changing the access code each time the remote control is used. The door opener responds to each new code only once. An access code copied from a working system and tried again will not control the door opener.

Lighted Wall Control*

Operates door opener from inside garage.

(Refer to section 3)

and Car2U®compatible.

Follow the Homelink

®

or Car2U®instructions in your car

owner’s manual.

*Opener MUST be installed with the

included Wall Control.

SAFETY FEATURES

Safe-T-Beam®Non-Contact Reversing System**.

Puts an invisible beam across the door opening. The door stops and reverses to the full open position if anything passes through the beam. Red or green LED indicator lights on the power head provide a self diagnostic code if an operational problem exists. (Refer to Section 10.)

Safe-T-Reverse

®

Contact Reversing System.

Automatically stops and reverses a closing door within 2 seconds of contact with an object. (Refer to Section 6.)

Safe-T-Stop

®

Timed Reversed System.

Automatically opens a closing door if it fails to close completely within 30 seconds.

Watch Dog

™

Monitoring System.

Monitors the Safe-T-Beam® system to ensure proper function­ality and will automatically stop and reverse a closing door if a problem is detected.

Automatic Lighting System.

Twin bulb lighting supplies up to 120 watts of light for safer evening exits and entries. Turns ON when door is activated and automatically turns OFF 3 minutes later.

Manual Emergency Release.

Manually releases door from door opener. Use during a power failure or other emergency to allow manual opening and closing of door. (Refer to Section 6.)

**Safe-T-Beam®Safety Reverse System

MUST be installed to close door.

SECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PAGE

SAFETY INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

OPENER FEATURES. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

SAFETY FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

PRE-INSTALLATION CHECK LIST . . . . . . . . . . . . . . . . . . . . . . . 4-5

RECOMMENDED TOOLS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

PARTS IDENTIFICATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-7

KEY ILLUSTRATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

SAFETY INSTALLATION INFORMATION . . . . . . . . . . . . . . . . . . . . 9

INSTALLATION

1 OPENER ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-11

2 OPENER INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . 12-14

3 WALL CONTROL INSTALLATION . . . . . . . . . . . . . . . . . 15-16

4 SAFE-T-BEAM

®

SYSTEM INSTALLATION . . . . . . . . . . . 17-18

5 CONNECTING TO POWER . . . . . . . . . . . . . . . . . . . . . . . . . 19

ADJUSTMENTS

6 LIMIT SWITCHES & FORCE ADJUSTMENT . . . . . . . . . 20-22

KEYED EMERGENCY RELEASE . . . . . . . . . . . . . . . . . . . . 21

CONTACT REVERSE TEST . . . . . . . . . . . . . . . . . . . . . . . . . 22

7 PROGRAMMING REMOTE CONTROLS. . . . . . . . . . . . . . . 23

8 BATTERY/ VISOR CLIP INSTALLATION . . . . . . . . . . . . . . . 24

9 LIGHT BULB AND LENS INSTALLATION . . . . . . . . . . . . . . 24

SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

MAINTENANCE & TROUBLESHOOTING

10 ROUTINE MONTHLY MAINTENANCE . . . . . . . . . . . . . . . . 25

WIRING DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

TROUBLESHOOTING GUIDE - OPENER. . . . . . . . . . . . . . 27

TROUBLESHOOTING GUIDE - POWER HEAD LED . . . . . 28

TRANSMITTER COMPLIANCE STATEMENT . . . . . . . . . . . . . . . 29

WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

PN# 37026500123 02/26/2010 REV. 1

6

To avoid damage to your door and/or

opener, make sure you disable and/or remove any door locks, ropes, and/or cables (NOT door lift cables) prior to installing your opener

. (

Refer to Section 1.)

4

PRE-INSTALLATION CHECK LIST

FOR HELP-1.800.354.3643 OR WWW.GENIECOMPANY.COM

Things to consider if you are planning to "Do-it-yourself."

This opener is designed for use with SECTIONAL doors only.

In many cases you will be replacing an existing door opener with a new one, however, if this will be the first opener installed there are some pre-installation issues which need to be addressed. They are as follows:

The Genie Company recommends that you read and fully understand all information and instructions contained herein before choosing a "Do-it-yourself" installation. Any questions should be directed to The Genie Company or an authorized Genie

®

Dealer.

1

Check your ceiling where the power head of your new unit will be mounted.

Plan how you will be mounting the power head. It is possible that ceiling joists may not be in the position needed with respect to the garage door opener. It may be necessary to add an additional bracket and

fasteners (not included

with your new door opener kit).

(Refer to Section 2.)

2

Check the wall directly above the garage door

. The door opener’s header bracket

must be securely fastened to this wall. Insure that the structure will provide a strong mounting location. (

Refer to Section 2.)

3

Check to see if the mounting location for the Safe-T-Beam

®

System is clear from obstruction and has a wood surface available for attaching the mounting brackets

. The

brackets may be attached to concrete if necessary but extra tools and special fasteners (not supplied) will be required.

(Refer to Section 4 and 5.)

NOTE: Mounting brackets must be installed within code specifications.

4

Is your sectional garage door made of

aluminum, light-weight steel, fiberglass

or glass panels

? Additional support bracing

must be added to these type doors. If this is the case, please contact the door manufacturer or authorized dealer so that they can furnish you with a "bracing kit."

(Refer to Section 2.)

7

Insure that your door is properly balanced and moving freely. (

Refer to Section 10.)

If your door jams, binds, is improperly balanced or has a broken spring, have it repaired or adjusted by a trained door system technician. Door springs, cables, pulleys, brackets and associated hardware are under extreme tension and can cause serious injury or death.

WARNING

(

The issue numbers below refer to the circled numbers in the illustrations on page 5.

)

8

(NOT SHOWN) If your garage does not have a separate entry door, you should consider

an emergency release kit (GER-2)for installation on your garage door.

DO NOT USE AN EXTENSION CORD! DO NOT USE A PORTABLE GENERATOR! This product is designed to operate on standard house current. DO NOT USE ALTERNATE POWER SUPPLIES.

WARNING

5

You need a properly grounded 110-120 Volt

power supply available

. The outlet should be

no more than 3 feet from the power head once it is mounted.

(Refer to Section 5.)

Remove

Remove

To reduce the risk of injury to persons or damage to property - Use this opener only with sectional doors.

WARNING

PN# 37026500123 02/26/2010 REV. 1

5

TYPICAL SECTIONAL DOOR INSTALLATION

FOR HELP-1.800.354.3643 OR WWW.GENIECOMPANY.COM

TYPICAL SUPPORT

BRACKET

(NOT PROVIDED)

EXTENSION SPRING

OR

TORSION SPRING

SAFE-T-BEAM

®

SENSORS

BRACES

ADDED HEADER BRACKET MOUNTING BOARD

POWER CORD

(APPROX. 45 IN.)

TO 120V GROUNDED

OUTLET

4

1

3

6

2

3

5

SECTIONAL DOOR

Pg. 19

Pg. 13

Pg. 12-13

Pg. 14

Pg. 11

Pg. 17-18

Pg. 17-18

MAX. 6" MIN. 5"

Pg. 25

To reduce the risk of injury to persons or damage to property - Use this opener only with sectional doors.

WARNING

7

NOTE: This opener is designed for use with SECTIONAL doors only.

PN# 37026500123 02/26/2010 REV. 1

6

RECOMMENDED TOOLS

FOR HELP-1.800.354.3643 OR WWW.GENIECOMPANY.COM

3/16" Drill Bit

1/4", 7/16", 3/8" and

1/2" Sockets

Step ladder

Drill

Ratchet

Carpenter’s level

Pencil

Tape measure

Wire strippers

Phillips screwdriver

Adjustable wrench

PARTS IDENTIFICATION

-

Not Shown Full Size .

Three-button

Remote Control

Safety Brochures

Entrapment Warning

Label

Safe-T-Beam

®

Source

with wire

(Red LED)

Safe-T-Beam

®

Sensor

with wire

(Green LED)

Wire

Insulated Staple

Door

Bracket

Header Bracket

Rail Section Clamp

Safe-T-Beam

®

Source/Sensor Bracket

ARRANGING BOX CONTENTS FOR ASSEMBLY

ORGANISATION DU CONTENU DE LA BOÎTE POUR LE MONTAGE

DISPOSICIÓN DEL CONTENIDO DE LA BOLSA PARA EL MONTAJE

Remove internal boxes.

Enlever les boîtes internes.

Quite las cajas internas.

Arrange three small boxes for easy access.

Arranger les trois petites boîtes de manière à

pouvoir y accéder facilement.

Disponga las tres cajas pequeñas para tener

acceso fácil.

Arrange rails in line and pull plastic sleeve off chain

or plastic tie off belt.

Arranger les rails en ligne et tirer sur le manchon en plastique

pour le dégager de la chaîne ou cravate en plastique

outre de courroie.

Disponga los rieles en línea y estire la camisa de plástico fuera

de la cadena o lazo plástico de la correa.

Remove lens Box and motor power head.

Enlever la boîte des lentilles et la tête motorisée.

Quite la caja de la lente y el motor de la caja de control.

Carefully remove third rail (with chain or belt

attached) and place on floor.

Enlever soigneusem*nt le troisième rail (avec la chaîne ou courroie attachée) et le placer sur le sol.

Cuidadosamente quite el tercer riel (con la

cadena o correa acoplada) y ponga en el

piso.

Remove rail sections not connected

to chain or belt.

Enlever les sections de rail non connectées

à la chaîne ou courroie.

Quite las secciones de riel no conectadas a

la cadena o correa.

Follow instructions in the Installation Manual for assembly steps.

Procéder selon les instructions stipulées dans le manuel d'installation pour les étapes de

©Overhead Door Corporation 02/2009

Box Contents Sheet

Head Rail (Chain) Section

Center Rail Section

End Rail Section

Door Arm

Hammer

Safety Glasses

Head Rail (Belt) Section

Pro Rail (Chain) Section

Pro Rail (Belt) Section

OR

Wall Control

(varies with model)

PN# 37026500123 02/26/2010 REV. 1

FASTENERS

-

Shown Full size (

See Parts List below for full description.)

Lag screw - 5/16" x 2"

Self-drilling Screw

1/4 -20 x 3/4"

Hex Flange Nut

1/4 -20

Cotter pin

Clevis pin

5/16" x 3/4"

Hex Bolt - 5/16 -18 x 3/4"

Hex Flange Nut

5/16 -18

Rail Clamp Bolt - 5/16 -18 x 5/8"

#10-16 x 1-1/4" Phillips Hex Screw

Hex Bolt - 5/16 -18 x 1/2"

#4-24 x 1" Pan Head

Phillips Screw

Clevis pin, long 5/16" x 3"

7

BAG NO. DESCRIPTION QUANTITY

0 RAIL SECTION CLAMP 2

RAIL CLAMP BOLT – 5/16 -18 x 5/8'' 8

HEX FLANGE NUT – 5/16 -18 8

1 BOLT – 5/16 -18 x 1/2'' 3

2 CLEVIS PIN, LONG – 5/16" x 3" 1

COTTER PIN 1

HEADER BRACKET 1

LAG SCREW – 5/16'' x 2'' 2

3 HEX BOLT – 5/16 -18 x 3/4'' 5

HEX FLANGE NUT – 5/16 -18 5

LAG SCREW – 5/16'' x 2'' 2

4 SELF DRILLING SCREW – 1/4 -20 x 3/4'' 3

DOOR BRACKET 1

5 HEX BOLT – 5/16 -18 x 3/4'' 3

SELF LOCKING NUT – 5/16 -18 1

HEX FLANGE NUT – 5/16 -18 2

CLEVIS PIN – 5/16" x 3/4" 1

COTTER PIN 1

6 WALL CONTROL ASSEMBLY 1

PAN HEAD PHILLIPS SCREW – #4-24 x 1'' 2

7 13 MM INSULATED STAPLE 30

8 Safe-T-Beam®SOURCE/SENSOR BRACKET 2

PHILLIPS HEX SCREW – #10-16 x 1- 1/4'' 4

WIRE NUT (GREY) 4

NO NUMBER

REMOTE WITH BATTERY 1

NO BAG Safe-T-Beam®SOURCE/SENSOR & WIRE SET 1

NO NUMBER

LIGHT COVER - WHITE 2

Self Locking Nut

5/16 -18

Wire Nut

MISSING ANY PARTS?

Please call toll free - 1.800.354.3643 DO NOT RETURN TO POINT OF PURCHASE. IMPORTANT! - Information needed when calling

• Model number - (located on packaging)

• Store, city, state, and date of purchase

Shoulder Bolt

5/16 -18 x 1"

PN# 37026500123 02/26/2010 REV. 1

8

1-PIECE RAIL HARDWARE ASSEMBLED VIEW

FOR HELP-1.800.354.3643 OR WWW.GENIECOMPANY.COM

3-PIECE RAIL HARDWARE ASSEMBLED VIEW

Tensioner

Rail with chain

Chain

Carriage Slide

Release Knob

Header Bracket

Power Head

Power Cord

Clevis Pin, Long & Cotter Pin

N

O

T

E

Some do

ors need

b

ra

cin

g. Con

tac

t

doo

r distributor or

manufactur

er

for

instructions.

HIGH SPRING TENSION

C

an

C

ause

Seriou

s I

n

ju

r

y

o

r D

e

ath

R

e

p

a

i

r

s

o

r

a

d

j

u

s

t

m

e

n

t

s

m

u

s

t

b

e

m

a

d

e

b

y

a

t

r

a

i

n

e

d

s

e

r

v

ic

e

p

e

r

s

o

n

u

s

i

n

g

p

r

o

p

e

r

t

o

o

l

s

a

n

d

i

n

s

t

r

u

c

t

i

o

n

s

Rail with belt

Belt

Carriage Slide

Belt Clamp

Rail Clamps

Rail Clamp Bolts

Rail Clamp Nuts

Tensioner

Rail with chain

Center Rail

End Rail

Chain

Carriage Slide

Release Knob

Header Bracket

Clevis Pin, Long & Cotter Pin

Power Head

Power Cord

N

O

T

E

Som

e doors

need

bracing.

Con

tac

t

doo

r distr

ibutor or

manufac

turer

for

instr

uct

ions

.

H

IG

H

S

P

R

ING

TEN

SI

O

N

Can

Cau

se Se

rio

u

s Inju

r

y o

r Death

Rep

airs

or

ad

jus

tme

nts

mu

st be

made by a t

rai

ned

service

per

son using

p

rop

er too

ls

and i

nstr

uct

ion

s

Rail with belt

Center Rail

End Rail

Belt

Release Knob

N

O

T

E

Som

e do

ors need

bracing.

Con

tac

t

door distr

ibut

or or

manufac

turer

for

instr

uct

ions

.

HIG

H

S

PR

ING

TEN

SI

O

N

C

an

Cause Se

rio

u

s Inju

r

y or Death

Rep

airs

or adjustme

nts

mu

st be

made

by

a t

rai

ned

service per

son using

p

rop

er too

ls

and i

nstr

uct

ion

s

CHAIN

CHAIN

BELT

BELT

PN# 37026500123 02/26/2010 REV. 1

9

OPENER ASSEMBLY

FOR HELP-1.800.354.3643 OR WWW.GENIECOMPANY.COM

1

NOTE: Three (3) piece rail assemblies are for a 7 foot high sectional door.

Clear a workspace area to unpack and organize box and contents for assembly.

1. There are 4 boxes inside the carton. Each box is

numbered 1 - 4. Note that some openers will

contain the same parts and be packaged with fewer boxes. Carefully remove the three

internal boxes (Labeled #1, 2, and 3) and place them on the floor for easy access (Fig. 1-1).

These boxes contain assembly parts and the contents are organized by assembly tasks. For quick reference inside the lid of each box there is a label illustrating the components inside.

2. Remove the motor power head and place it on the floor for later use. Remove box #4 and place it on the floor for later use.

Do NOT run until opener is fully assembled and

instructed to do so.

CAUTION

FIG. 1-1 Internal boxes.

RAIL ASSEMBLY: Use a clean, flat surface.

Rail Connectors

Rail Connector Bolts

Rail Connector Nuts

Box Label Example

#4

1.

READ AND FOLLOW ALL SAFETY, INSTALLATION AND OPERATION INSTRUCTIONS.

(If you have questions or do not understand an instruction, call The Genie Company or an authorized Genie

®

Dealer.)

2. Install only on a properly balanced sectional garage door.

An improperly balanced door could cause severe injury. Have a trained door system technician make repairs or adjustments to cables, spring assemblies, and other hardware before installing the opener.

3. Remove all ropes and remove or make inoperative all locks connected to the garage door before installing opener.

4. Where possible, install the door opener 7 feet or more above the floor. For products having an emergency release, mount the emergency release 6 feet above the floor.

IMPORTANT INSTALLATION INSTRUCTIONS

WARNING:

To reduce the risk of severe injury or death:

5. Do NOT connect the opener to source of power

until instructed to do so.

6. Locate the Wall Control:

• Within sight of door,

• At minimum height of 5 feet so small children are not able to reach it, and

• Away from all moving parts of the door.

7. Install the Entrapment WARNING Label next to the Wall

Control in a prominent location. Install the Emergency Release Tag on or next to the emergency release.

8. After installing the opener, the door must reverse within 2 seconds when it contacts a 1-1/2 inch high object (or a 2 x 4 board laid flat) on the floor.

To reduce the risk of injury to persons or damage to property - Use this opener only with sectional doors.

WARNING

NOTE: For 1-piece rail—skip to POWER HEAD & RAIL ASSEMBLY.

NOTE: Please follow ALL instructions in their NUMBERED sequence. Use wall control and safety sensors provided with this unit. Do NOT substitute wall control or safety sensors.

10

FIG. 1-2 Split Rail sections.

FIG. 1-3 Split Rail assembly.

A

B

Chain Rail

Center Rail

End Rail

Wire Tie(s)

Rail Assembly for CHAIN DRIVE OPENER

NOTE: For split rail clamps, nuts, and bolts locate Bag 0 from Box 1.

3. Remove the two rail sections that are not connected to the chain and place them on floor (Fig. 1-2, A).

4. Carefully remove the third rail section with chain and plastic sleeve. Place rail section on floor and extend chain straight out (Fig. 1-2, B). Chain and rail should extend

approximately 7 feet.

5. Remove wire ties and plastic bag from chain. Leave chain extended straight out on floor.

Avoid kinks in the chain by careful handling and keeping chain flat on the floor.

6. Align the three rail sections by pulling the chain straight and wrapping it around the chain tensioner pulley (Fig. 1-3 & 1-4).

7. Attach the two rail clamps to the rail section joints with (4) bolts and nuts. After both rail

clamps have been assembled to the rail sections, securely tighten the bolts and nuts.

PN# 37026500123 02/26/2010 REV. 1

Rail Clamps

Rail Clamp Bolts

Rail Clamp Nuts

Rail with chain

Center Rail

End Rail

Chain

Carriage Slide

Release Knob

Power Head

N

O

T

E

S

o

m

e

do

o

rs

n

e

e

d

b

ra

c

in

g

.

C

o

n

ta

c

t

d

oor d

istrib

u

t

o

r o

r

m

a

nu

fa

ct

ur

er

for

ins

tr

uc

t

io

n

s

.

H

I

G

H

S

P

R

IN

G

T

E

N

S

I

O

N

C

a

n

C

a

u

s

e S

e

r

i

o

u

s

I

n

ju

ry o

r

De

a

t

h

R

e

p

a

i

r

s

o

r

a

d

j

u

s

t

m

e

n

t

s

m

u

s

t

b

e

m

a

d

e

b

y

a

tr

a

i

n

e

d

s

e

r

v

i

c

e

p

e

r

s

o

n

u

s

i

n

g

p

r

o

p

e

r

t

o

o

l

s

a

n

d

i

n

s

t

r

u

c

t

i

o

n

s

Rail with belt

Center Rail

End Rail

Belt

Release Knob

N

O

TE

So

m

e

d

o

or

s

n

e

e

d

br

a

cin

g

.

C

o

n

ta

c

t

d

o

or distrib

u

t

o

r o

r

m

a

nu

fa

c

t

ur

e

r

fo

r

instr

u

ct

io

n

s.

H

I

G

H

S

P

R

I

N

G

T

E

N

S

I

O

N

C

a

n

C

a

u

s

e

S

e

r

io

u

s

I

n

ju

r

y

or

D

e

a

t

h

R

e

p

a

i

r

s o

r

a

d

j

u

s

t

m

e

n

t

s

m

u

s

t

b

e

m

a

d

e

b

y

a

tr

a

i

n

e

d

s

e

r

v

i

c

e

p

e

r

s

o

n

u

s

in

g

p

r

o

p

e

r

t

o

o

l

s

a

n

d

i

n

s

t

r

u

c

t

i

o

n

s

Rail Assembly for BELT DRIVE OPENER

NOTE: For split rail clamps, nuts, and bolts locate Bag 0 from Box 1.

3. Remove the two rail sections that are not connected to the belt and place them on floor (Fig. 1-2, A).

4. Carefully remove the third rail section with belt. Place rail section on floor, remove ties on belt and extend belt straight out (Fig. 1-2, B).

Avoid twists and kinks in the belt by careful handling and keeping belt flat on the floor. Belt and rail should extend approximately 7 feet.

5. Align the three rail sections by pulling the belt straight and wrapping it around the tensioner pulley (Fig. 1-3 & 1-4).

6. Attach the two rail clamps to the rail section joints with (4) bolts and nuts. After both rail

clamps have been assembled to the rail sections, securely tighten the bolts and nuts.

Belt Rail

Center Rail

End Rail

CHAIN DRIVE RAILS

BELT DRIVE RAILS

FIG. 1-4 Mount chain/belt to tensioner pulley.

Wrap around tensioner pulley

CHAIN

BELT

A

B

Chain Tensioner Pulley

Tensioner Pulley

POWER HEAD & RAIL ASSEMBLY

Assembly for CHAIN DRIVE OPENER

NOTE: Handle carefully! Drive chain can slide out of rail.

NOTE: For power head and rail assembly locate Bag 1 from Box 1.

NOTE: Copy serial number from power head frame and record it on warranty page.

1. Attach rail assembly to power head by aligning the sprocket onto the motor shaft. Use (3) bolts, 5/16 -18 x 1/2" (Fig. 1-5).

2. Tighten the chain by turning the adjustment nut clockwise. The chain adjustment nut is

located in the Chain Pulley Bracket (opposite rail end from the power head) (Fig. 1-6).

3. Tighten chain until chain is approximately 1/8 inch above the base of the rail at midpoint on the rail (Fig. 1-6). Do NOT over tighten chain.

Set assembled power head and rail aside. Begin with Section 2 INSTALLATION.

PN# 37026500123 02/26/2010 REV. 1

11

FIG. 1-6 Chain adjustment.

FIG. 1-5 Rail - Power head assembly.

Chain Pulley Bracket (at wall end of rail)

Chain

T-Rail at center of rail assembly

1/8"

T-Rail

Chain

Tighten nut to move pulley this direction

Use 1/2" socket

on adjustment nut

Use

5/16"-18 x 1/2"

Bolts

FIG. 1-8 Disable garage door lock.

Remove

Remove

FIG. 1-7 Belt adjustment.

Belt Pulley Bracket (at wall end of rail)

Belt

T-Rail at center of rail assembly

1/8"

T-Rail

Belt

Tighten nut to move pulley this direction

Use 1/2" socket

on adjustment nut

Assembly for BELT DRIVE OPENER

NOTE: For power head and rail assembly locate Bag 1 from Box 1.

NOTE: Copy serial number from power head frame and record it on warranty page.

1. Attach rail assembly to power head by aligning the sprocket onto the motor shaft. Use (3) bolts, 5/16 -18 x 1/2" (Fig. 1-5).

2. Tighten the belt by turning the adjustment nut clockwise. The belt adjustment nut is located in

the Belt Pulley Bracket (opposite rail end from the power head) (Fig. 1-7).

3. Tighten belt until belt is approximately 1/8 inch above the base of the rail at midpoint on the rail (Fig. 1-7). Do NOT over tighten belt.

Set assembled power head and rail aside. Begin with Section 2 INSTALLATION.

You should have removed all ropes and/or cables (NOT door lift cables) and disabled the door lock already. If you have not, remove all ropes and/or cables and disable garage door lock NOW before continuing with installation (Fig. 1-8).

CAUTION

You should have removed all ropes and/or cables (NOT door lift cables) and disabled the door lock already. If you have not, remove all ropes and/or cables and disable garage door lock NOW

before continuing

with installation (Fig. 1-8).

CAUTION

12

PN# 37026500123 02/26/2010 REV. 1

FIG. 2-2 Finding highest point of travel.

OPENER INSTALLATION

FOR HELP-1.800.354.3643 OR WWW.GENIECOMPANY.COM

2

HEADER AND DOOR MOUNTING BRACKETS:

1. Finding header bracket mounting location.

• Close garage door.

– Use a pencil and level.

a) Mark center of garage door (one-half overall

width) on the wall with 6" vertical line at top edge of door.

b) Continue this line on wall above door for

about 12" (Fig. 2-1, a).

• Raise garage door until top edge of door

reaches its maximum height

(Fig. 2-2)

.

• With door at highest point.

–

Measure height from top edge of door to floor

(Fig. 2-2).

• Close door again.

• Mark height measurement on wall above door

(Fig. 2-1, c)

.

– Make your mark across vertical line made earlier.

• Add 2-1/2" to height mark just made on

wall. This

is location for header bracket (Fig. 2-1, d).

NOTE: If header bracket location needs to be above header for garage door opening, you need to add a "mounting surface." A 2" x 6" board securely attached (board and fasteners not included) to wall studs on either side of your mark is sufficient (Fig. 2-3).

NOTE: For header bracket and bolts locate Bag 2 from Box 1.

NOTE: The bolts supplied in Bag 2 are designed to be used on pressure treated lumber.

2. Mounting the header bracket.

• Hold header bracket against wall

(Fig. 2-3).

• Position bracket as shown.

–

Place center on vertical line,

–

Bottom edge on final height line.

•

Mark screw hole locations on wall.

• Drill 3/16" pilot holes at each screw hole mark.

–

Fasten header bracket with 2 lag screws (provided) (Fig. 2-3).

FIG. 2-1 Final height mark.

Header bracket must be fastened to garage framing. Do NOT fasten to drywall, particle board, plaster or other such materials.

WARNING

2-1/2"

top of door

in closed

position

d) - final

height mark

HIGHEST POINT OF TRAVEL

TRACK

SECTIONAL

DOOR

HEADER

FROM HERE

TO FLOOR

2-1/2"

HIGHEST POINT OF TRAVEL

TRACK

SECTIONAL

DOOR

HEADER

FROM HERE

TO FLOOR

a) - 6" vertical

line

b) - extend

vertical line

c) - door at

highest point

door at highest point

door at highest point

final height mark

final height

mark

2-1/2"

FIG. 2-3

Header bracket mounting (on header & above header)

.

Door springs are under high tension. If spring or its shaft is in the way, measure 2-1/2" above spring or shaft on the garage door centerline and mark this height as your location for header bracket.

Do NOT move door spring!

WARNING

MOUNTING THE OPENER:

1. Getting started.

• Position assembled rail

on wall next to header

bracket

(Fig. 2-4).

– Place material on floor under power head to

protect from scratching. (A box, stool, or similar device may be needed to clear a torsion spring.)

NOTE: For header bracket pins locate Bag 2 from Box 1.

2. Mounting the assembly.

• Attach rail to header bracket using clevis pin

and cotter pin (Fig. 2-5).

• Support power head on step-ladder to prevent

interference with header mounted (torsion) spring.

NOTE: Before final attachment to ceiling, insure that assembly is in proper alignment (Fig. 2-4).

NOTE: For nuts, bolts, and lag screws locate Bag 3 from Box 1.

• On finished ceilings, locate ceiling joists or

trusses using a stud finder or similar device. Attach angle iron (not provided) to joists or trusses through finish material using (provided) lag screws (Fig. 2-6).

• On unfinished ceilings or open ceilings, straps

may attach directly to joists or trusses. Depending on the garage construction, extra framing material (not provided) which may be required should be installed using appropriate construction techniques (Fig. 2-6).

NOTE: Refer to your local building codes for appropriate construction techniques.

• Attach mounting straps (not provided) to ceiling

using lag bolts (Fig. 2-6).

• Set height of power head to following

(Fig. 2-6).

a)

Rail must clear door at door’s highest point

of travel.

b)

Rail must b

e level or at power head end

slightly below level.

• Securely tighten power head mounting bolts

and nuts.

• Carefully raise and lower door manually.

Ensure door does not contact any section of power head or rail.

• Check that rail clamp bolts and nuts are tight.

• DO NOT PLUG OPENER IN YET!

FIG. 2-4 Position assembly and align.

VIEW

FROM ABOVE

(not to scale)

HEADER BRACKET

Mounting Straps

(not provided)

FIG. 2-6 Mounting the power head.

ANGLE IRON ON FINISHED CEILING

Attach angle iron to beams

UNFINISHED OR OPEN BEAM

Extra framing

not needed

Extra framing

NEEDED

DRYWALL

bolts & nuts

bolts & nuts

FIG. 2-5

Rail mounting to header bracket

.

COTTER PIN

CLEVIS PIN

(Chain drive

shown)

PN# 37026500123 02/26/2010 REV. 1

13

14

PN# 37026500123 02/26/2010 REV. 1

DOOR BRACKET:

NOTE: For door bracket and bolts locate Bag 4 from Box 2.

1. Finding door bracket mounting location.

• Door bracket is mounted as high on

door as

possible along vertical centerline and NO LOWER THAN top set of rollers (Fig. 2-7).

2. Mounting the door bracket.

• Proper bracing should be verified at this point.

–

Align door bracket centered on your vertical centerline (Fig. 2-8).

–

Attach using 3 self-drilling screws for sheet metal or other light weight material.

–

Use lag screws (not provided) for solid

wooden sectional doors.

NOTE: For solid wood doors, carriage bolts WITHOUT SLOTTED HEADS (not included) may also be used for attaching door bracket.

INSTALL DOOR ARMS

NOTE: For door arm nuts and bolts, clevis and cotter pins locate Bag 5 from Box 2.

1. Attach the arms.

• Fasten short branch of curved door arm to door

bracket using bolt and locking nut (Fig. 2-9).

• Fasten straight arm to carriage using clevis pin

and cotter pin (Fig. 2-9).

2. Connecting the arms.

•

Slide carriage back and forth to adjust arm length. – Position the straight arm 50º down from the

rail.

• With the arms arranged in this position, fasten

arms together using bolts and nuts spaced as far apart as possible (Fig. 2-9).

Doors made of masonite, lightweight wood, fiberglass, and sheet metal must be properly braced before mounting door opener. Contact door manufacturer or distributor for a bracing kit. The Genie Company is not responsible for damage caused due to improperly braced door.

CAUTION

FIG. 2-7 Mounting door Bracket

.

centerline

even with or

above top roller

FIG. 2-9 Attaching door arms.

FIG. 2-8 Examples of door bracket positioning.

A B

centerline

50°

short clevis pin & cotter pin

bolts as far

apart as

possible

PN# 37026500123 02/26/2010 REV. 1

NOTE: Wall control will not operate until limits are set.

NOTE: For Wall Control, wire and insulated staples locate Bags 6 and 7 from Box 2.

1. Wall Control location.

• Wall Control location should be in direct sight of door.

• It should be at least five feet (5') above floor to prevent small children from operating door.

• It must be away from any moving parts. (You should NOT be able to reach the garage door while standing at Wall Control.)

• Wall Control board screw connections are

polarized, (+) positive and (-) negative.

2a. Wiring (If pre-wired).

• Locate Wall Control pre-wired wire ends (Fig. 3-1). (They should be located within the guidelines mentioned above.)

• Split and strip ends of wire (Fig. 3-2).

• Fasten wire to Wall Control board screws on back of Wall Control. – Striped wire to the + (plus) terminal. – White wire to the - (minus) terminal.

2b. Wiring (If NOT pre-wired).

• Pick a convenient location for mounting Wall Control using the guidelines mentioned above (Fig. 3-1).

• Run wire from power head to Wall Control

(Fig. 3-1).

• Split and strip ends of wire (Fig. 3-2).

• Fasten wire to Wall Control board screws on back of Wall Control. – Striped wire to the + (plus) terminal. – White wire to the - (minus) terminal.

WALL CONTROL INSTALLATION

FOR HELP-1.800.354.3643 OR WWW.GENIECOMPANY.COM

3

Verify there is NO power to the opener before installing Wall Control wires and Wall Control.

WARNING

Staples which are too tight can cut or pinch wires. Cut or pinched wires can cause the Wall Control to stop working. When using the insulated staples, make sure you fasten them only as tightly as needed to hold the wire snugly.

CAUTION

FIG. 3-2 Splitting and stripping

.

FIG. 3-1 Wall Control wire routing

Wire from power head to Wall Control

Wall Control

"Entrapment" warning label

Separate entry door

EXAMPLE ONLY!

This is an example of wire routing when NOT pre-wired. Your wire routing may be different.

1/2"

2"

15

Black Striped

White

+

–

or

or

Use of any other wall control can cause the door to operate unexpectedly and the light not to work. Use only the included Wall Control.

WARNING

PN# 37026500123 02/26/2010 REV. 1

16

3. Securely fasten wires.

• Securely fasten wires to ceiling and wall using insulated staples provided. – Use insulated staples. – Staples should be snug only.

• If rear cover is attached to power head, remove it.

• On power head: – Route Wall Control wires through wire guide

on power head.

– Split and strip ends of wire (Fig. 3-2 on

previous page).

– Insert wire into terminal holes and lightly press in

the orange locking clips above each terminal hole. (You can use a pencil or small screwdriver to comfortably press in locking clips.) The white wire into #1 terminal hole and striped wire into the #2 terminal hole.

– Confirm wire lock by lightly tugging on the wire.

The wire should remain in the terminal hole.

• Do NOT install rear cover yet.

4. Mounting.

• Fasten Wall Control to wall with 2 screws (provided) (Fig. 3-4).

• Remove protective backing from "Entrapment" warning label (Fig. 3-5). The "Entrapment" label is located in the center of this manual. – Stick label on wall near Wall Control.

FIG. 3-4 Mounting Wall Control.

Insulated

Staple

+–

PB

Infared Sensor

123456

FIG. 3-3 Insert wires

.

(Power Head With Rear Cover Removed)

FIG. 3-5 Mounting Entrapment warning label.

3

2

1

Independent Light Control

–

Controls door opener lights from inside garage

–

Energy-Saver shut-off turns OFF lights 3 minutes after

door activation

Vacation Locking Switch

– LOCK disables controls after door is completely closed

– UNLOCK allows controls to work normally

Door Control "Open/Close" Button

–

Open and closes door from

inside garage

wire guide

PN# 37026500123 02/26/2010 REV. 1

17

SAFE-T-BEAM®SYSTEM INSTALLATION

FOR HELP-1.800.354.3643 OR WWW.GENIECOMPANY.COM

4

NOTE: The opener will not close the door automatically unless the Safe-T-Beam

®

System is

installed. NOTE: For Sensors, screws, wire, and insulated

staples locate items and Bag 8 from Box 3.

1. Mounting brackets.

• Mark both sides of garage door frame or wall no higher than 6" and no lower than 5" above floor

(Fig. 4-1)

.

• Hold bracket against door frame or wall. – Check if brackets extend out from wall far

enough, so tongue of bracket is beyond door, tracks or any door hardware.

– If not:

a) Mounting bracket extensions are available

through an authorized Genie

®

Dealer.

b) Blocks of wood, etc. may be substituted for

extensions.

• Locate top of bracket on your mark (Fig. 4-2).

• Fasten each with 2 screws (Fig. 4-2).

NOTE: Mounting brackets can be attached to the floor or concrete rim using concrete anchors (not provided) obey manufacturer’s instructions.

2. Mounting Safe-T-Beam®Source (Red LED) and Sensor (Green LED).

• If garage has only one garage door.

– Determine which side of garage receives most

direct sunlight (Fig. 4-4).

– Red LED should always be on sunny side

whenever possible (Fig. 4-4).

• For multiple doors.

– Preventing crossed signals is critical. – Place source and sensor modules on adjacent

doors facing in opposite directions (Fig. 4-4).

NOTE: To help prevent interference from sun, Safe-T-Beam

®

sensor with Green LED may be placed further away from the door opening, though extended no further out from the wall, where it will spend more time in shadow.

• Slide source/sensor onto tongue of bracket until

it clicks into place (Fig. 4-3).

3a. Wiring (If NOT

pre-wired).

• Route wire from Safe-T-Beam

®

sensors to power

head using method shown in (Fig. 4-5a).

• Securely fasten wires to wall and ceiling as you go (Fig. 4-6 on next page).

– Use insulated staples. – Staples should be snug only.

There should be no electrical power to the opener while installing Safe-T-Beam

®

wires. If you have

plugged in the power cord—UNPLUG IT NOW!

WARNING

FIG. 4-1 Mark door frame

.

FIG. 4-2 Mounting brackets

.

FIG. 4-3 Attach sensors to brackets

.

bracket

tongue

mark

FIG. 4-4 Safe-T-Beam

®

source and sensor

locations

.

FIG. 4-5a Source and sensor wiring methods

.

SensorSource

Red Green

Power Head

Dashed Line = striped wire

Solid Line = white wire

Insulated

Staple

center of

bracket

PN# 37026500123 02/26/2010 REV. 1

18

3b. Wiring (pre-wired).

• Route wire from wall to Safe-T-Beam

®

sensors

(Fig. 4-5b).

• Splice pre-wiring to shortened sensor wire, match wire pairs dash-to-dash (striped-to- striped) and plain-to-plain (white-to-white).

- Trim sensor wire to approximately one foot

(1 ft) from sensor.

- Split and strip ends of sensor wires and

pre-wired wires (Fig. 4-7).

- Splice wires together with (provided)

wire nuts.

• Route wire from ceiling to power head (Fig. 4-5b).

• Securely fasten wires where they exit wall and ceiling as you go.

– Use insulated staples. – Staples should be snug only.

4. Split and strip ends of sensor wires (Fig. 4-7).

NOTE: For rear cover locate Box 4.

5. Attach Safe-T-Beam®wire to power head wire terminal.

• Route Safe-T-Beam

®

wires through wire guide on power head. – Insert wire into terminal holes and lightly press

in the orange locking clips above each terminal hole. (You can use a pencil or small screwdriver to comfortably reach in and lightly press down locking clips.) Insert white wires to 'even' numbered terminal holes and striped wires into 'odd' terminal holes (Fig. 4-8).

– Confirm wire lock by lightly tugging on the wire.

The wire should remain in the terminal hole.

• Do not install the white (lamp) cover at this time.

NOTE: Safe-T-Beam®alignment check must be performed following connection to electrical power (see page 19). DO NOT PLUG IN YET!

Staples which are too tight can cut or pinch wires. Cut or pinched wires can cause the Safe-T-Beam

®

System to stop working. When using the insulated staples, make sure you fasten them only as tightly as needed to hold the wire snugly.

CAUTION

FIG. 4-7 Splitting and stripping

.

FIG. 4-6 Wire routing

.

+–

PB

Infared Sensor

123456

FIG. 4-8 Insert wires

.

(Power Head With Rear Cover Removed)

FIG. 4-5b Pre-Wired source and sensor wiring

methods

.

SensorSource

Red Green

Power Head

Dashed Line = striped wire

Solid Line = white wire

Wall Wall

Ceiling

1/2"

2"

Insulated

Staple

Wire Nut

wire guide

PN# 37026500123 02/26/2010 REV. 1

19

CONNECTING TO POWER

FOR HELP-1.800.354.3643 OR WWW.GENIECOMPANY.COM

5

Plug the opener into a properly grounded electrical outlet (Fig. 5-1).

• To reduce the risk of electrical shock, this equipment has a grounded type plug that includes a third (grounding) pin. This plug will only fit a grounded type outlet. If you do not have a grounded outlet, contact a qualified licensed electrician to install one. DO NOT alter the plug in any way. The door opener must be properly grounded in order to prevent personal injury and damage to the components.

• DO NOT remove motor cover. All work performed on motor must be done by a trained door system technician.

WARNING

• Check local building codes to make sure that you

are not required to have your garage door opener permanently wired, with circuit breaker protection. If building codes require door opener to be permanently wired have a qualified licensed electrician connect power with permanent wiring.

CAUTION

WITH GROUNDED PLUG:

5

" m

in

f

r

om

fl

o

o

r

6

" m

ax

f

r

o

m f

l

o

o

r

FIG. 5-4 Check Safe-T-Beam®alignment

.

FIG. 5-1 Connect to power

.

INFRARED PROTECTION FUNCTION

1. When the garage door is opening, its movement will not be influenced if the Safe-T-Beam®is obstructed.

2. If the Safe-T-Beam

®

is obstructed before the

garage door fully closes, the door will not close.

3. When the garage door is closing, if Safe-T-Beam

®

is cut off by people or obstacle, the garage door will reverse automatically to its fully opened position. (Meanwhile, the opener light will keep blinking until door moves to its fully opened position.)

4. If the Safe-T-Beam

®

System fails, loses power, or is installed improperly, press and hold the Wall Control "open/close" button until the door reaches its fully closed position. The LED indicator light on the power head will be green and blink twice (Pattern: ☼☼ pause ☼☼ pause) to inform you to eliminate the problem first. If you release the "open/close" button on the Wall Control during the closing movement the door will reverse automatically to its fully opened position.

FIG. 5-2 Remove motor cover.

(Electrican ONLY)

WITH PERMANENT WIRING:

Instructions for Electrician.

• Remove power from circuit.

• Remove rear cover and motor cover.

– Remove four motor cover screws (Fig. 5-2).

• Remove existing power cord and strain relief

from the 7/8" dia. hole and discard (Fig. 5-3).

• Connect permanent wiring to power head using 7/8" diameter hole. – White to white/black to black/ground to green. – Use only UL recognized wire nuts.

• Wires inside the power head must be at least 6" in length.

• Replace motor cover and rear cover and re-energize the circuit.

NOTE: The Genie Company is not responsible for charges resulting from work performed by an independent electrician.

Check Safe-T-Beam®alignment (Fig. 5-4).

• Insure that no part of door or its hardware is in path between lenses of source and sensor.

• Insure that tops of lenses are between 5" - 6" above the floor (Fig. 5-4). The brackets are flexible, and can be adjusted slightly if needed.

• Adjust the Red LED transmitter by aiming the unit directly at the Green LED receiver. Use the adjustment screw located on the top of the transmitter housing to make adjustments.

• The Red LED transmitter will blink if there is a misalignment. When the LED units are aligned the Red LED will remain ON continuously.

• After the alignment is finished tighten the adjustment screws on both sensors.

Motor Cover Screws

FIG. 5-3 Power cord strain relief.

• Do NOT use an extension cord.

• Do NOT use a portable generator. This product

is designed to operate using standard household current.

• Do NOT use alternate power supplies.

CAUTION

WITH POWER SUPPLIED:

PN# 37026500123 02/26/2010 REV. 1

20

DOOR LIMITS

FOR HELP-1.800.354.3643 OR WWW.GENIECOMPANY.COM

6

The OPEN (UP) and CLOSE (DOWN) door positions are controlled by making the adjustments on the panel located on the bottom of the power head. The adjustments that can be made are:

• Close Travel Limit,

• Open Travel Limit,

Adjust Closing Force Adjust Opening Force Transmitter Programming

SETTING & TESTING OPEN/CLOSE LIMITS

FIG. 6-1 Limit controls.

• Severe injury or death can result if the door

closing force is set too high.

• Never increase the door closing force above the minimum required to move the door.

• Never adjust force to compensate for a sticking or binding door.

• Perform monthly CONTACT REVERSE TEST as described on page 22 and in Section 10.

WARNING

Limit Controls location on power head.

B) CLOSE TRAVEL LIMIT

1. Press and hold the "Close Travel Limit" button

until the door is fully closed.

2. You can quickly press and release the "Close Travel Limit" button to move the door in small increments. You can also use the "Open Travel Limit" button to move the door slightly in the

UP direction.

3. Door is fully closed when the bottom edge of door

presses firmly onto the ground.

4. Once the door is in the desired position, press and hold the "Close SET Limit" button for 5 seconds. The LED indicator light will blink green once. This stores the closed position in memory.

C) OPEN TRAVEL LIMIT

1. Press and hold the "Open Travel Limit" button

to move the door to its fully opened position. This starts the opener moving in the UP direction.

2. Hold the "Open Travel Limit" button until the door is in the fully opened position that you desire, then release this button.

3. You can quickly press and release the "Open Travel Limit" button to move the door in small increments. You can also use the "Close Travel Limit" button to move the door slightly in the

DOWN direction.

4. Once the door is in the desired position, press and hold the "Open SET Limit" button for 5 seconds. The LED indicator light will blink green twice. This stores the opened position in memory.

SET

SET

Carriage Assembly

Chain Connector

Latch Movement

Latch Movement

Move in this direction

Carriage Assembly

Belt Connector

Latch Movement

Latch Movement

M

ove in this directi on

FIG. 6-2 Engage Chain/Belt Connector to Carriage.

Operation of the opener without the Chain or Belt Connector engaged to the Carriage Assembly will result in damage to rail components including the rail pulley.

CAUTION

A) ENGAGE CHAIN/BELT CONNECTOR TO CARRIAGE

1. Press and hold the "Close Travel Limit" button

until the chain or belt connector advances and engages to the Carriage Assembly (Fig. 6-2).

Failure to verify the engagement of the belt/chain connector will result in damage to rail components.

CAUTION

NOTE: Set Close Travel Limit

before setting Open Travel Limit for unit to operate normally.

Unless limits are being reset do not press set limit buttons.

21

FIG. 6-3 Engage/Disengage Carriage Lock.

CARRIAGE LOCK

The Carriage Lock can be manually engaged or disengaged.

• To disengage Carriage Lock

– Pull handle downward opener power head.

• To engage Carriage Lock

– Pull handle towards door.

Obtain standard emergency release kit and remove S-hook from the cable end that attaches to the opener carriage.

1. Attach the emergency release cable loop end to

the opener carriage as shown (FIG 6-4).

Properly connecting the release cable to the carriage fitting will enable the correct carriage release action for the opener.

KEYED EMERGENCY RELEASE (PURCHASED SEPARATELY)

FIG. 6-4 Emergency release cable to carriage.

Improper connection of the emergency release cable to the opener carriage will result in a failure of the emergency release.

WARNING

2. Follow the remaining installation instructions for

the standard emergency release kit.

3. Test for correct operation of emergency release kit. Keyed Emergency Release Operation Instructions

• Place key in slot.

• Rotate and hold key while lifting garage door 1 to

2 inches.

• Release key and continue opening garage door.

NOTE: The next normal operation of the opener or fully closing garage door manually will re-engage the emergency release mechanism.